Popular Posts

Chapter 3 - 1



●     First standard for STP was 802.1D
●     Common Spanning Tree (CST) assumes one 802.1D spanning-tree instance for the entire bridged network, regardless of the number of VLANs. Lower CPU/memory requirements but also can lead to suboptimal traffic flows and slow converging times
●     Per VLAN Spanning Tree Plus (PVST+) - Cisco enhancement of STP that provides for a separate 802.1D spanning-tree instance for each VLAN configured in the network. Supports PortFast, BPDU guard, BPDU filter, root guard, and loop guard. More CPU and memory needed but traffic flow can also be optimized per VLAN
●     Rapid STP (RSTP) is 802.1w - Faster convergence than STP but still has single instance of STP so still can lead to suboptimal traffic flow issues.
●     Multiple Spanning Tree (MST) - Maps multiple VLANs that have same traffic flow requirements into the same spanning-tree instance. Cisco implementation provides up to 16 instances of RSTP )802.1w) and combines many VLANs with the same physical and logical topology into a common RSTP instance. Each instance supports PortFast, BPDU Guard, BPDU filter, root guard, and loop guard.
●     PVRST+ is Cisco enhancement of RSTP and similar to PVST+. Provides separate instance of 802.1w per VLAN. Separate instances support PortFast, BPDU guard, BPDU filter, root guard and loop guard. Addresses both the convergence issues and suboptimal traffic flow.


Protocol
Standard
Resources Needed
Convergence
VLANS
CST
802.1D
Low
Slow
All VLANs
PVST+
Cisco
High
Slow
Per VLAN
RSTP
802.1w
Medium
Fast
All VLANs
PVRST+
Cisco
Very High
Fast
Per VLAN
MSTP
802.1s
Medium/High
Fast
VLAN List

●     PVST+ is the default STP that is enabled with VLANs created in Cisco switches
●     STP and RSTP work as follows
○     Forces certain ports into standby state so they do not listen, forward, or flood data frames. Only one path to each network segment active at a time
○     If connectivity issues arise, STP or RSTP reestablishes connectivity by activating an inactive path
●     STP Operation:
○     Elects root bridge - All ports are designated. Root is either with lower priority or if priorities are the same, lower MAC address number
○     Selects root port on all nonroot bridges. Root port is the lowest-cost path from the nonroot bridge to the root bridge. Root ports send/receive traffic. If two equal cost paths, it’ll select the port with the lowest port ID. Port ID = configurable priority + port number.
○     Selects designated port on each segment - lowest path cost to the root bridge.

Port Role
Description
Root Port
Exists on nonroot bridges. Best path to root bridge. Forwards all traffic toward the root bridge. Source MAC address of frames received on root port can populate the MAC table. Only one root port enabled per bridge
Designated Port
Exists on root and nonroot bridges. On Root bridge, all ports are designated. Nonroot bridges - designated port is the switch port that receives and forwards data frames toward the root bridge as needed. Only one designated root port enabled per segment. If Designated ports can populate MAC table
Nondesignated Port
Not forwarding (blocking) data frames and not populating MAC address table

Disabled Port
Port that is shut down

●     Five port states:
○     Blocking - Nondesignated and not forwarding. Received BPDUs to determine location and root switch and which port roles each switch should assume in final active STP topology. Default, port spends 20 seconds in this state (max age)
○     Listening - STP decided port can participate in forwarding and has started transmitting it’s own BPDU’s and informing adjacent switches it’s preparing to participate in the topology. Default, port spends 15 seconds in this state (forward delay)
○     Learning - Prepares to participate in frame forwarding and starts populating CAM table. Defaul, port spends 15 seconds in this states (forward delay)
○     Forwarding - Port is considered part of active topology. Forwards frames and sends/receives BPDUs
○     Disabled - Does not participate in STP and does not forward frames at all

●     Root port determined by cost and cost is associated to speed.
○     10 Gbps = Cost 1
○     1 Gbps = Cost 4
○     100 Mbps = Cost 19
○     10 Mbps = Cost 100
●     Default priority for port is 128
●     RSTP defines additional port roles of Alternate and Backup and defines port states as discarding, learning or forwarding.
●     RSTP can revert to STP in mixed environment but it will negate the benefits of RSTP for that segment
●     RSTP has only three port states corresponding to the three possible operational statuses

Port State
Description
Discarding
Seen in both stable topology and topology synchronization/changes. Prevents the forwarding of data frames and breaks the continuity of Layer 2 loops
Learning
Seen in stable topology and synchronization/changes. Learning state accepts data frames to populate MAC table to limit flooding of unknown unicast frames
Forwarding
Only seen in stable topologies. Only occurs after proposal and agreement process

Comparison of 802.1D and RSTP port states:

Operational Status
STP Port State
RSTP Port State
Port Included in Active Topology
Enabled
Blocking
Discarding
No
Enabled
Listening
Discarding
No
Enabled
Learning
Learning
Yes
Enabled
Forwarding
Forwarding
Yes
Disabled
Disabled
Discarding
No

●     With RSTP, port roles and port states can transition independently of each other.
●     RSTP Port Roles:
○     Root - Switch port on every nonroot bridge that is the chosen path to the root bridge
○     Designated - One designated port for a segment. Assumes forwarding state.
○     Alternate - Offers alternative path toward root bridge. Assumes a discarding state in stable, active topology. Present on nondesignated switches and makes transition to designated port if current designated port fails.
○     Backup - Additional switch port on designated switch with a redundant link to the segment for which the switch is designated. Has a higher port ID than the designated port on the designated switch. Assumes a discarding state in stable active topology
○     Disabled - No role within the operation of spanning tree

No comments:

Post a Comment